Field Armor
D3O Vest
Icon | D3O Vest
Icon adjustable fit.
Injected Molded Armor Plates
Chest Protector Tested and Certified According to Standard FprEN 1621-3 2017, Level Back Protector Tested and Certified According to Standard EN 1621-2 : 2014, Level 2
Integrated I.C.E (Emergency Contact Info) Badge, Low-profile Design Fits Under Most Jackets and Suits
Jacket Sizing Information
There are three variables to consider when sizing an ICON jacket. The first two are the chest and sleeve measurements, which are what your jacket size is based on. The third is the the jacket fit type, which defines the “cut” of the jacket (Attack, Sport, or Relaxed). Instructions, sizing charts and jacket fit details can be found below. The fit type of every Icon jacket can be found in the first bullet point of the copy block for that individual product.
- Attack
- Sport
- Relaxed
Chest measurement instructions
While standing with your arms relaxed at your side, wrap a flexible tape measure around your chest at its largest point. The tape measure should go through your armpit and stay parallel with the floor while taking the measurement.
Sleeve measurement instructions
While standing with your arms relaxed at your side, place one end of a flexible tape measure on your spine at the base of your neck. Measure over the top of your shoulder, down over the point of your elbow, and finish at the wrist bone.
Womens Jacket Sizing Chart
- Size
- XS
- S
- M
- L
- XL
- 2XL
- 3XL
Womens Jacket Conversion Chart
Care Instructions
General Care
ICON® vests are tough and designed to withstand a great deal of asphalt induced abuse, but no vest can survive every conceivable motorcycle accident. Should the unfortunate occur and you crash in your Icon vest thoroughly review the product for any signs of structural damage (major abrasion, holes, damaged seams, etc). Should there be any damage or if you are unsure if the damage is structural you should replace the vest. Most Icon textile vests use a coating on the shell material which reinforces the overall fabric matrix. Improper cleaning of the jacket could compromise the integrity of this coating leading to material failure. Unnecessary exposure to Sunlight and UV rays should be avoided. This is most critical when storing your vest. Always store your vest in a dark, well ventilated area. Vests are best hung on a wide padded hanger. Do not wrap in plastic or other nonporous materials as this may cause the fabric to discolor. Finally, avoid exposing your vest(or any of your riding gear) to fumes or vapors from gasoline or any harsh chemicals. These fumes weaken the structure of nylon and polyester textiles lessening their inherent protective capabilities.
Pre-Cleaning
It is important to follow a few simple steps to prepare your vest for washing. Remove the insulated liner from the vest (if so equipped). When removing the liner unsnap each snap carefully - DO NOT apply excessive force - as this may break the snap. Remove all impact protectors from the vest. Make sure to close and fasten all the pocket flaps.
Cleaning
Insulated Liner - Hand wash the insulated liner in warm water with a mild liquid laundry detergent. Thoroughly rinse insulated liner with clean water to remove all detergent. Should you desire to clean the impact protectors they can be cleaned by wiping the protectors with a damp cloth.
Vest (Textile Areas) - Hand wash the vest with warm water and a mild liquid laundry detergent. Hand washing minimizes unnecessary stress on the garment. A soft bristle toothbrush works well in helping to remove any bug strikes or road debris. Rinse the vest with clean water to remove all detergent. DO NOT use any form of oxygenated detergent, bleach, fabric softeners, or dry cleaning chemicals. These items will damage the vest!
Drying
Insulated Liner - The insulated liner should be allowed to drip dry-only. DO NOT use a machine dryer, direct sunlight, hair dryers or any type of heater during the drying process.
Vest - DO NOT use a machine dryer. Subjecting the vest to a machine dryer will damage the vest and possibly the dryer itself. The only recommended method for drying the vest is drip-drying. Do not subject the vest to direct sunlight, hair dryers or any type of heater during the drying process. DO NOT use an iron on any part of the garment.
Replacement Parts
Product Manual
D3O
The Level 2 custom-molded D3O® chest and back piece offer a higher level of impact protection. The unique patented technology provides a versatile, flexible material for a host of shock absorption applications.
