Men's
Uparmor
Uparmor
ICON® relaxed fit
10oz Cotton/Polyester Fleece Chassis
300D Polyester Internal Reinforcements
D30 Removable Back, Elbow and Shoulder Ghost Impact Protectors - EN 1621-2:2014 / EN 1621-1:2012
Reflective Trims
Jacket Sizing Information
There are three variables to consider when sizing an ICON jacket. The first two are the chest and sleeve measurements, which are what your jacket size is based on. The third is the the jacket fit type, which defines the “cut” of the jacket (Attack, Sport, or Relaxed). Instructions, sizing charts and jacket fit details can be found below. The fit type of every Icon jacket can be found in the first bullet point of the copy block for that individual product.
- Attack
- Sport
- Relaxed
Chest measurement instructions
While standing with your arms relaxed at your side, wrap a flexible tape measure around your chest at its largest point. The tape measure should go through your armpit and stay parallel with the floor while taking the measurement.
Sleeve measurement instructions
While standing with your arms relaxed at your side, place one end of a flexible tape measure on your spine at the base of your neck. Measure over the top of your shoulder, down over the point of your elbow, and finish at the wrist bone.
Mens Jacket Sizing Chart
- Size
- XS
- S
- M
- L
- XL
- 2XL
- 3XL
- 4XL
- 5XL
Mens Jacket Conversion Chart
Care Instructions
General Care ICON® jackets are tough and designed to withstand a great deal of asphalt induced abuse, but no jacket can survive every conceivable motorcycle accident. Should the unfortunate occur and you crash in your Icon jacket thoroughly review the product for any signs of structural damage (major abrasion, holes, damaged seams, etc). Should there be any damage or if you are unsure if the damage is structural you should replace the jacket. Most Icon textile jackets use a coating on the shell material which reinforces the overall fabric matrix. Improper cleaning of the jacket could compromise the integrity of this coating leading to material failure. Unnecessary exposure to Sunlight and UV rays should be avoided. This is most critical when storing your jacket. Always store your jacket in a dark, well ventilated area. Jackets are best hung on a wide padded hanger. Do not wrap in plastic or other nonporous materials as this may cause the fabric to discolor. Finally, avoid exposing your jacket (or any of your riding gear) to fumes or vapors from gasoline or any harsh chemicals. These fumes weaken the structure of nylon and polyester textiles lessening their inherent protective capabilities.
Pre-Cleaning It is important to follow a few simple steps to prepare your jacket for washing. Remove the insulated liner from the jacket (if so equipped). When removing the liner unsnap each snap carefully - DO NOT apply excessive force - as this may break the snap. Remove all impact protectors from the jacket. Make sure to close and fasten all the pocket flaps.
Cleaning Insulated Liner - Hand wash the insulated liner in warm water with a mild liquid laundry detergent. Thoroughly rinse insulated liner with clean water to remove all detergent. Should you desire to clean the impact protectors they can be cleaned by wiping the protectors with a damp cloth. Jacket (Textile Areas) - Hand wash the jacket with warm water and a mild liquid laundry detergent. Hand washing minimizes unnecessary stress on the garment. A soft bristle toothbrush works well in helping to remove any bug strikes or road debris. Rinse the jacket with clean water to remove all detergent. DO NOT use any form of oxygenated detergent, bleach, fabric softeners, or dry cleaning chemicals. These items will damage the jacket!
Drying Insulated Liner - The insulated liner should be allowed to drip dry-only. DO NOT use a machine dryer, direct sunlight, hair dryers or any type of heater during the drying process. Jacket - DO NOT use a machine dryer. Subjecting the jacket to a machine dryer will damage the jacket and possibly the dryer itself. The only recommended method for drying the jacket is drip-drying. Do not subject the jacket to direct sunlight, hair dryers or any type of heater during the drying process. DO NOT use an iron on any part of the garment.
Product Manual
D30® Ghost Impact Protectors
D3O Ghost™ Impact Protectors are made with the revolutionary new D3O Impact Print™ technology which allows for unrivaled freeform geometry and flexibility. The superior breathability of Ghost armor makes it perfect for summer riding jackets and pants. At only 0.65cm thick, the low-profile design is an ideal retrofit to many motorcycle apparel applications.
